In this article down the page you'll find a lot of really good information and facts on the subject of How to Install a Bathtub Yourself.
Setting up a bath tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old tub with a new one is likewise a reasonably tough project. If the old tub is conveniently easily accessible, the task can move rapidly; if you have to open up a wall to remove the old bathtub and place the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to vacate the old bathtub and also set in the new one. Ensure you have actually certified on your own for the work and also fit trying it. As opposed to working with a contractor to take over a halfway-completed project, it is far better to take into consideration using one prior to you begin. Possibilities are you may need a professional plumber to make tube links.
This write-up will certainly assist you set up a brand-new bath tub in your bathroom if you have already bought a new tub and don't need to change the arrangement of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be quite problematic as a result of the limited access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the other end gives a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Secure the faucet in place with the supplier provided backnut. When the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal faucet connectors. The previous type should be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, position the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and readjusting the feet on the bathtub up until the level reads level.
To set up faucets, fit the bottom of the furthest flexible tap connector to the ideal supply pipeline by making a compression join; after that do the same for the various other faucet.
Activate the water system as well as examine all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub as well as additionally inspect the overflow outlet and also the typical electrical outlet for leaks.
Lastly, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the tub ought to wait till the bathtub has actually been made use of at least once as this will resolve it right into its final position.
Planning for the Installment
To start with, the supporting framework supplied with the bath must be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bath tub.
Fit the versatile tap adapters to the bottom of both taps utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom fulfills the floor tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to split an inflexible seal, creating the water to penetrate the wall between the bathroom as well as the tiling, leading to complications with dampness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your components as well as installations. They are marketed in tubes and also cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealer can split fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the marketplace. It is suggested to fit the floor tiles utilizing water-resistant or water-proof adhesive as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic reader about How to Install a Bathtub Yourself, I was thinking sharing that portion was a smart idea. If you please take the time to distribute this blog if you enjoyed it. We enjoy reading our article about How to Install a Bathtub Yourself.
Visit Homepage